Power Supply 5V 10A

Description

If you’re looking to supply a stable power to your project, you will definitely need one of this. The power supply comes in a metal casing, which is great for ventilation and heat dissipation. Setting up is very simple, just connect the AC cable to the input and output wires to your setup. There is a potentiometer inside the casing to allow for small tuning of voltage if necessary.

FEATURES

Universal AC input / Full range
Protections: Short circuit / Overload / Over voltage
Cooling by free air convection
LED indicator for power on
100% full load burn-in test
All using 105°C long life electrolytic capacitors
Withstand 300VAC surge input for 5 second
High operating temperature up to 70°C
Withstand 5G vibration test
No load power consumption<0.5W
High efficiency, long life and high reliability
3 years warranty

NOTE:

All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25°C of ambient temperature
Ripple & noise are measured at 20MHz of bandwidth by using a 12″” twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor
Tolerance: includes set up tolerance, line regulation and load regulation
Line regulation is measured from low line to high line at rated load
Load regulation is measured from 0% to 100% rated load
Length of set up time is measured at cold first start. Turning ON/OFF the power supply very quickly may lead to increase of the set up time.
3.3V, 5V when the load factor 0~50%, the switching power less is reduced by burst operation, which will cause ripple and ripple noise to go beyond the specifications.
The ambient temperature derating of 5°C/1000m is needed for operating altitude higher than 2000m(6500ft)
The power supply is considered a component which will be installed into a final equipment. All the EMC tests are been executed by mounting the unit on a 360mm*360mm metal plate with 1mm of thickness. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to “”EMI testing of component power supplies”” (as available on http://www.meanwell.com)

OUTPUT:

DC Voltage: 5V
Rated Current: 10A
Current Range: 0 ~ 10A
Rated Power: 50W
Ripple & Noise (max) [Note 2]: 80mVp-p
Voltage Adj. Range: 4.5 ~ 5.5V
Voltage Tolerance [Note 3]: ±2.0%
Line Regulation [Note 4]: ±0.5%
Load Regulation [Note 5]: ±1.0%
Setup, Rise Time: 1000ms, 30ms/230VAC; 2000ms, 30ms/115VAC at full load
Hold Up Time (Typ.): 30ms/230VAC; 12ms/115VAC at full load

INPUT:

Voltage Range: 85 ~ 264VAC 120 ~ 373VDC
Frequency Range: 47 ~ 63Hz
Efficiency (Typ.): 83.0%
AC Current (Typ.): 0.95A/115VAC; 0.56A/230VAC
Inrush Current (Typ.): COLD START 45A/230VAC
Leakage Current: <0.75mA / 240VAC

PROTECTION:

Overload: 110 ~ 150% rated output power; Protection type : Hiccup mode, recovers automatically after fault condition is removed
Over Voltage: 5.9~ 7.3V; Protection type : Hiccup mode, recovers automatically after fault condition is removed

ENVIRONMENT:

Working Temperature: -30 ~ +70°C (Refer to “”Derating Curve””)
Working Humidity: 20 ~ 90% RH non-condensing
Storage Temperature, Humidity: -40 ~ +85°C, 10 ~ 95% RH
Temperature Coefficient: ±0.03%/°C (0 ~ 50°C)
Vibration: 10 ~ 500Hz, 5G 10min./1cycle, period for 60min. each along X, Y, Z axes

SAFETY & EMC [Note 6]:

Safety Standards: UL60950-1, TUV EN60950-1, EN60335-1, EN61558-1/-2-16,CCC GB4943.1, BSMI CNS14336-1, EAC TP TC 004, AS/NZS 60950.1(by CB) approved
Withstand Voltage: I/P-O/P:4KVAC; I/P-FG:2KVAC; O/P-FG:1.25KVAC
Isolation Resistance: I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25°C / 70% RH
EMC Emission: Compliance to EN55032 (CISPR32) Class B, EN55014, EN61000-3-2,-3, GB/T 9254, BSMI CNS13438, EAC TP TC 020
EMC Immunity: Compliance to EN61000-4-2,3,4,5,6,8,11, EN61000-6-2 (EN50082-2), heavy industry level, criteria A, EAC TP TC 020

OTHERS:

MTBF: 645Khrs min. MIL-HDBK-217F (25°C)
Dimension: 99*82*30mm (L*W*H)
Weight: 0.23kg

Shipping List

1x Power Supply 5V 10A